continental device india limited an is/iso 9002 and iecq certified manufacturer pnp silicon planar epitaxial transistor bc369 to-92 bce transistor in to-92 plastic packa g e intended for low volta g e , hi g h current lf a pp lications , suitable for class-b audio out p ut sta g es u p to 3w absolute maximum ratings description symbol value unit collector -emitter voltage vces 25 v collector -emitter voltage vceo 20 v emitter base voltage vebo 5.0 v collector current ic 1.0 a collector current peak value icm 2.0 a base current ib 100 ma base current peak value ibm 200 ma power dissipation @ ta=25 deg c pta 0.8 w @ tc=25 deg c ptc 1.0 w junction temperature tj 150 deg c storage temperature range tstg -65 to +150 deg c thermal resistance junction to ambient in free air rth (j-a) 156 deg c/w junction to ambient * rth (j-a) 125 deg c/w junction to case rth (j-c) 60 deg c/w *mounted on printed-circuit board , maximum lead length 4mm, mounting pad for collector lead min 10 mm x10 mm electrical characteristics (ta=25 deg c unless otherwise specified) description symbol test condition min typ max unit collector cut- off current icbo ie=0, vcb=25v - - 10 ua - tj=150 deg c ie=0, vcb=25v - - 1.0 ma emitter cut- off current iebo veb=5v, ic=0 - - 10 ua base- emitter on voltage vbe(on) ic=5ma, vce=10v - 0.7 v ic=1a, vce=1v - 1.0 v collector- emitter saturation voltage vce(sat) ic=1a, ib=100ma - - 0.5 v is/iso 9002 lic# qsc/l- 000019.2 is / iecqc 700000 is / iecqc 750100 continental device india limited data sheet page 1 of 3
electrical characteristics (ta=25 deg c unless otherwise specified) description symbol test condition min typ max unit dc current gain hfe ic=5ma, vce=10v 50 - - ic=500ma,vce=1v 85 - 375 hfe group ic=500ma,vce=1v -10 63 160 -16 100 250 -25 160 400 ic=1a, vce=1v 60 - dynamic characteristics collector capacitance cc ie=0, vcb=5v,f=450khz - - 60 pf transition frequency ft ic=10ma,vce=5v,f=35mhz 40 - mhz to-92 transistors on tape and ammo pack to-92 plastic package to-92 bulk to-92 t&a 1k/polybag 2k/ammo box 200 gm/1k pcs 645 gm/2k pcs 3" x 7.5" x 7.5" 12.5" x 8" x 1.8" 5.0k 2.0k 17" x 15" x 13.5" 17" x 15" x 13.5" 80.0k 32.0k 23 kgs 12.5 kgs package net weight/qty details standard pack inner carton box qty outer carton box qty gr wt size size p ac ki ng d eta il cumulative pitch error 1.0 mm/20 pitch to be measured at bottom of clinch at to p of bo dy t1 0.3 - 0.6 body width body height body thickness pitch of component feed hole pitch feed hole centre to component centre distance between outer leads component alignment tape width hold-down tape width hole position hold-down tape position lead wire clinch height component height length of snipped leads feed hole diameter total tape thickness lead - to - lead distancef1, clinch height pull - out force item a1 a t p po p2 f h w wo w1 w2 ho h1 l do t f2 h2 (p) symbol specification 4.0 4.8 3.9 6n min. 12.7 12.7 6.35 5.08 0 18 6 9 0.5 16 4 2.54 nom. 4.8 5.2 4.2 1 23.25 11.0 1.2 3 max. 1 0.3 0.4 +0.6 -0.2 0.5 0.2 +0.7 -0.5 0.2 0.5 0.2 +0.4 -0.1 tol . remarks notes 1. maximum alignment deviation between leads not to be greater than 0.2 mm. 2. maximum non-cumulative variation between tape feed holes shall not exceed 1 mm in 20 pit ch es . 3. holddow n tape not to exceed beyond the edge(s) of carrier tape and there shall be no exposure of adhesive. 4. no more than 3 consecutive missing components are permitted. 5. a tape trailer, having at least three feed holes are required after the last component. 6. splices shall not interfere w ith the sprocket feed holes. all dimensions in mm unless specified otherwise ammo pack s t y le adhesive ta p e on to p side flat side mechanical data t t1 t f1 f2 f p2 po do (p) w2 wo w1 w h1 a a1 p h0 l flat side of transistor and adhesive tape visible 2000 pcs./ammo pack label carrier strip 8.2" 1 3 " f e e d 1 . 7 7 " h h b 3 2 1 a k e d a a sec aa g d f f h c 3 2 1 3 2 1 all diminsions in mm. dim min. max. a 4.32 5.33 b 4.45 5.20 c 3.18 4.19 d 0.41 0.55 e 0.35 0.50 f5 deg g 1.14 1.40 h 1.14 1.53 k 12.70 ? pin configuration 1. base 2. collector 3. emitter continental device india limited data sheet page 2 of 3
disclaimer notes the product information and the selection guides facilitate selection of the cdil's discrete semiconductor device(s) best suited for application in your product(s) as per your requirement. it is recommended that you completely review our data sheet(s) so as to confirm that the device(s) meet functionality parameters for your application. the information furnished on the cdil web site/cd is believed to be accurate and reliable. cdil however, does not assume res ponsibility for inaccuracies or incomplete information. furthermore, cdil does not assume liability w hatsoever, arising out of the application or use of any cdil product; neither does it convey any license under its patent rights nor rights of others. these pr oducts are not designed for use in life saving/support appliances or systems. cdil customers selling these pr oducts (either as individual discrete semiconductor devices or incorporated in their end products), in any life saving/support appliances or systems or applications do so at their own risk and cdil will not be responsible for any damages resulting from such sale(s). cdil strives for continuous improvement and reserves the right to change the specifications of its products without prior notic e. cdil is a registered trademark of continental device india limited c-120 naraina industrial area, new delhi 110 028, india. telephone + 91-11-579 6150 fax + 91-11-579 9569, 579 5290 e-mail sales@cdil.com www.cdil.com continental device india limited data sheet page 3 of 3
|
